iSeries Command Line Commands

 

Caution: This article is designed to help you learn some basic commands for the IBM iSeries. Not every user has the security to run all of the commands listed below. Make sure that you have permission to make any changes to your system before doing so. RJS Software does not accept any responsibilty for lost information or data due to using any of our Knowledge Base Articles.

Things To Know

• Help - Pressing F1 while the cursor is on a message, command, or value will often bring up a help screen with more information.
• Prompt - Pressing F4 after typing a command prompts a list of values that can be passed to that command. The prompt screen displays all available parameters and acceptable values for those parameters.
• Security - As stated above: Not every user has the security to run all of the commands listed below. Make sure that you have permission to make any changes to your system before doing so. RJS Software does not accept any responsibilty for lost information or data due to using any of our Knowledge Base Articles.

Command Line Length

Many commands are actually longer than the one or two lines typically given in the Command Line Interface.

• To display a larger command line, type: CALL QCMD
• To display a full page command line, type: CALL QCMD, F11

Displaying System Values

If you have any RJS Software product on the iSeries, you can run the following commands to display the OS/400 operating system version, serial number, model number, and partition (LPAR) number where the product is installed:

• General iSeries information: /PRDINFO
• Serial number: DSPSYSVAL QSRLNBR
• Model number: DSPSYSVAL QMODEL
• System name:
  • Type: DSPNETA
  • Press Enter.
  • See Local system.
• OS/400 version:
  • Type: GO LICPGM
  • Press Enter.
  • Type 10.
  • Press F11.
• AS/400 TCP/IP address:
  • Type: NETSTAT
  • Press Enter.
  • Type 1.
• To find system values (the long way):
  • Run: WRKSYSVAL
  • Next to the value you need, type 5.
  • Press Enter.

    The value displays.

    For example: To view the value for the serial number, type 5 next to QSRLNBR.

To Display System Operator Messages

1. Type: DSPMSG
2. Press F4.
3. Type: QSYSOPR
4. Press Enter.

   The messages display.

To Display the Session Job Log

1. Run: DSPJOBLOG
2. When the job log displays, press F10 to see a detailed log.
3. Page up from the bottom to see the most current activity.

Library and Library List Commands:

• To display your current library list: DSPLIBL
• To add a library to your library list: ADDLIBLE
• To remove a library from your library list: RMVLIBLE
• To see if a library is present: WRKLIB
• To find the current version of a RJS Software product library:
  • Run: DSPDTAARA
  • Press F4.
  • In Data area name, type VERSION.
  • In Library, type the library name.
• To display all the objects within a library: WRKOBJPDM

Output Queue and Report Commands

• To display all output queues: WRKOUTQ *ALL

  Note: This is helpful for checking whether an output queue's exists.

• To display a specific output queue: WRKOUTQ

  Note: You use the an asterix (*) as a wildcard character to display all output queues with similar names.

  Note: If you have the same output queue in multiple libraries, you may need to specify the library as well.

• To create an output queue: CRTOUTQ /

  Note: If you do not specify a library when you create the output queue, the output queue is created in the QGPL library by default.

• To clear an output queue (delete all spool files in the output queue): CLROUTQ /

  Note: If you do not specify a library name, it will clear the first output queue with the matching name in your library list.

• To delete an output queue: DLTOUTQ /

  Note: If you do not specify a library name, it will delete the first output queue with the matching name in your library list.

• To view reports by owner:
  • Run: WRKSPLF
  • Type 5 next to the appropriate user.
  • Press Enter.
  • Choose the output queue.

Viewing Directories and Files on the IFS (Integrated File System)

File structure on the IFS is similar to the UNIX file system (even the commands match). All directory or file paths start with a forward slash (/) to indicate the root of the system. The rest follows basic directory structures.

• To access the root directory on the IFS:
  • Run: WRKLNK "/"
  • Type 5 next to the folder to view its contents.
• To access a directory called RJSTEMP in the root of the IFS:
  • Run: WRKLNK "/RJSTEMP"
  • Type 5 next to the folder to view its contents.

Checking a User Profile

• To view all the user profiles: WRKUSRPRF *ALL
• To view a specific user profile: WRKUSRPRF
• User settings of importance (primarily for the WinSpool products):
  • STATUS should be ENABLED.
  • SET PASSWORD TO EXPIRE should be NO.
  • LIMIT CAPABILITIES - If *YES, RJS Software has a Notes technical document that tells you what commands you need. Search the document for limited* to access it.
  • Check the user class - *SECOFR indicates security officer level.

FTP Server Commands:

• To check on FTP server status:
  • Run: NETSTAT
  • Press Enter.
  • Type 3.

    If the FTP server is running, there will be and entry called FTP-CON in Local Port, and it will have a state of LISTEN.

• To start the FTP server: STRTCPSVR *FTP
• To end the FTP server: ENDTCPSVR *FTP
• To change FTP timeout:
  • Type: CHGFTPA
  • Press F4.

    Note: The inactivity time-out is 300 seconds (5 minutes) by default. Setting it to 0 indicates no time-out. After changing the FTP attributes, you must stop the FTP server and restart.

• To verify that you can log on to your iSeries FTP Server from DOS:
  • Go to the DOS prompt.
  • Type FTP
  • Press Enter.

    You should then be asked for a user ID and password. If this fails or doesn't happen, there is a problem connecting to the iSeries FTP server and RJS Software products will not work until this issue is resolved.

Need to secure your NFS Shares with WebDocs for iSeries?

Or, are you moving documents between IFS folders?